We will need:
– Yellow yarn (The author used Anne by Circulo yarn, 4 ply (14 wpi));
– gray yarn;
– black yarn;
– Hook 2 mm;
– Filler;
– Needles for stitching and scissors;
– A wire for his neck and arms;
– glue;
– Paint: black, white, gray, red and lime colors;
– White and gray felt;
– A piece of Eva materials or similar material;
– Black, red and white threads to embroider his name.
Body;
(do 6 – yellow thread):
Row 1: 14 VP, 13 sc (13)
Row 2-15: sc to each loop (13)
Close knitting and leave a long thread for
stitching.
1. Sew all the pieces together except the top.
2. Cut a piece of filler cubic
forms. You do not need additional
filler for the body.
3. Insert the cube from the filler into the part, and then sew the top.
Gray edge of the upper body:
Row 1: We make 38 sc using the Moogly’s method, which does not need a base (38) Close the knit.
This is what the top edge should look like when you sew it to the body:
– Gray corners “y” to the bottom (do 4):
Row 1: Make 5 sc using the Moogly’s method, which does not need a base (5)
Cut the yarn and leave a long thread for sewing.
Attach the yarn to the 3rd stitch and do 2 sc.
Close the knitting.
This part looks like when sewn to the body:
– Gray corners for the back of his back;
(do 2);
Row 1: Do 2 sc using the Moogly’s method, which does not need a base (2) Close the knit.
– The gray part located on its sides (do 2):
Row 1: We do 17 sc using the Moogly’s method, which does not need a base (17) Close the knit.
– The gray part with which his hands are attached (do 2):
Round 1: 6 sc to amigurumi ring (6)
Round 2: sc in each loop (6) Close knitting.
– Hands (do 2);
** Starting with a yellow thread
Round 1: 8 sc in amigurumi ring (8)
Round 2-14: sc to each loop (8)
Round 15: We knit only in the back of the loops. (2 sc, decrease) x 2 (6) ** change the thread to gray
Round 16-17: sc in a circle (6) Close the stew.
– Fingers (make 4 – gray thread):
Row 1: Doing 6 sc using the Moogly’s method, no base loops needed for it (6)
Row 2: sc in each loop (6)
Close knitting and leave a long thread for sewing.
– Feet (make 4 – black thread);
Row 1: By making 4 sc using the Moogly’s method, no base loops are needed for it (4)
Row 2-32: sc to each loop (32)
– Neck (yellow yarn);
Round 1: 6 sc to amigurumi ring (6)
Round 2-10: sc to each loop (6)
Close knitting and leave a long thread for sewing.
– eyes;
Handset (do 2);
Round 1: Make 10 sc in the Amigurumi Ring (10)
Round 2-8: sc in each loop (10) Close knitting.
Front part (do 2);
Round 1: 8 sc in amigurumi ring (8)
Round 2: Increase (16)
Round 3-9: sc in each loop (16) Close knitting.
Gray cylinder between the eyes;
Round 1: 6 sc to amigurumi ring (6)
Round 2-5: sc into amiugurmi ring (6)
Round 6: decrease (5) Close knitting.
Assembly;
1. Make his body. Sew all the squares together except the top, put the filler in and sew
the upper part, as indicated earlier;
2. Sew the Gray Edge onto the upper body:
3. Sew the gray “y” corners to the bottom:
4. Sew the gray corners from the back to the top:
5. Using gray felt, make 2 pieces as shown in the photo below and attach them to the body.
6. Using a gray felt, make the front panel and glue it.
7. Use a little filler and fill the part, then sew to the part where his hands will be.
8. Now, before sewing on his hands, add wire inside his body to keep his hands on
location. To insert the wire into the cube, the author used a needle to enlarge the hole. After that, the wire was already inserted.
Pierce the cube with a sharp needle
Enlarge the small hole with the large needle
Insert wire
Bend the wire next to his body and insert his hand through it.
9. To make the fingers, stitch the two parts together:
Then, cut two pieces of wire (they should be larger than the fingers) and bend them twice.
After that, insert the wire into your fingers.
Finally insert the wire into his hands and sew on his fingers:
10. Using white felt and black paint, make a part for the hands.
11. In order to make legs, first cut 2 pieces of wire and bend it into this shape (as in the photo below):
Sew two pieces of his leg with wire inside:
12. Cut a piece of wire and try to shape it. It will be his neck. Insert already
formed wire to his neck:
Then, insert the wire into his body:
After that, sew the neck to his body:
13. Now, we sew the gray cylinder between the eyes on his neck:
14. Use the material Eva and cut out 2 pieces for each eye:
Then, cut off two pieces of gray felt and glue to the previous parts.
We draw pupils and an iris:
After that, we place this part inside the front part and glue them.
Finally, we sew the eyes to the gray cylinder between the eyes:
Now, fill each part with filler and glue it to the back of each eye.
Do not forget to make a reflection in his eyes:
15. We make details on its front panel and embroider its name.
16. Using a black thread, make a chain of VP – these will be the wires that connect the eyes.
17: Using the Eva material we make gears and paint them with silver paint:
That’s all, your Valley is ready!
